• SD card speed class-compatible.
• Compatible with UHS-II
• Eye-Fi cards and Multimedia cards (MMC) are not supported.

• Self Cleaning Sensor Unit
  • Removes dust adhering to the low-pass filter.
  • At power off only / Enable / Disable. Performed automatically (taking about approx. 2 sec. as indicated on the screen) or manually (taking about approx. 7 sec. as indicated on the screen).
  • After manually activated cleaning, the camera will automatically restart (Power OFF to ON).
  • When [Multi Shot Noise Reduction], [Multiple exposures], or [HDR mode] is set, [Clean now] and [Clean manually] cannot be selected.
• Dust Delete Data acquisition and appending
  • The coordinates of the dust adhering to the low-pass filter are detected by a test shot and appended to subsequent images.
  • The dust coordinate data appended to the image is used by the EOS Canon Digital Professional Software to automatically erase the dust spots.
  • Not available in focus bracketing, RAW burst mode, or multiple-exposure shooting.
• Manual cleaning (by hand)

• Values for Recording Pixels are rounded to the nearest 100,000th.
• RAW/C-RAW images are generated at 3:2, with information added about the specified aspect ratio, and JPEG images are generated at the specified aspect ratio.
• These aspect ratios (M / S1 / S2) and pixel counts also apply to resizing.

• Continuous numbering
  • The numbering of captured images continues even after you replace the card.
• Auto reset
  • When you replace the card, the numbering will be reset to start from 0001. If the new SD card already contains images, the numbering will continue from the last recorded image in the card.

• Auto
• Standard
• Portrait
• Landscape
• Fine Detail
• Neutral
• Faithful
• Monochrome
• User Defined 1-3

1. Auto (Ambience priority/White priority)
2. Day Light
3. Shade
4. Cloudy1
5. Tungsten light
6. White fluorescent light
7. Flash
8. Custom2(Custom WB)
9. Color temperature

• Corrected in reference to the current WB mode's color temperature.
• Blue/amber and magenta/green shift can be set at the same time.

• Applies when an RF or RF-S lens without a focus mode switch is attached.
• When lenses with a focus mode switch are attached, the setting on the lens takes precedence.

1. Evaluative metering
2. Partial metering (approx. 6.0% of the area at the center of the screen)
3. Spot metering (approx. 3.0% of the area at the center of the screen)
4. Center-weighted average metering

Available ISO speeds; user-set

• For [Highlight tone priority], the settable ISO speed range will be ISO 200 to 32000.
• Expanded ISO cannot be set for HDR mode or during HDR PQ shooting.

User-defined ISO range - still photo shooting

User-defined Auto ISO range - still photo shooting

ISO Auto details in still photo shooting

*1ISO 200 when [Highlight tone priority] is set to [Enable] or [Enhanced].
*2Varies depending on [Maximum] and [Minimum] of [Auto range].
*3If outside the setting range, changed to the value most close to ISO 400.

• Auto AE lock
  • The metering mode for AE lock after focus can be customized.
• User-applied AE lock
  • In the Fv, P, Tv, Av and M modes, enabled with the AE lock button. (Press again to update.)
  • Enabled in all metering modes.

1. Mechanical
2. Electronic 1st-Curtain
3. Electronic Shutter (1st and 2nd curtain - silent*)

Based on Canon testing standards.

• Always on
• Only for shot

1. Evaluative (Face Priority)
2. Evaluative
3. Average

1. E-TTL each shot
2. E-TTL 1st shot

• Anti-smudge coating applied.
• Anti-reflection coating not applied.

1. Single image (select image)
2. Select range
3. All images in a folder
4. All images on card
   • Image browsing and image search can be based on ratings.
   • Ratings-based image selections also possible with DPP.
5. All found images (only during image search)

Except protected images

1. Select images to erase
2. Select range
3. All images in folder
4. All images on card
5. All found images (only during image search)